Oneshot and Multishot ESC Flashing guide
*IF YOU ARE FLASHING MULTISHOT PLEASE SEE THE NOTES BELOW*
PART 1: Flashing your multicopter ESCs with Oneshot or Multishot!
In this tutorial we look at how to get BLhelisuite working with 'one-wire-passthrough' so you can flash or upgrade your ESCs with one simple USB connection to your flight controller. As well as upgrading your ESC firmware we will see how simple it is to switch over to Multishot using the same software, if you so desire!
BLHelisuite download page:
Multishot download page:
Multishot notes: Your motors will not operate until you enable multishot function in the cleanflight CLI. Do the following (betafligh 2.6.1)
1. Leave oneshot *enabled* very inportant for this version of betaflight.
2. in the cli type: set use_multishot =ON (then press enter)
3. type: save (press enter)
If you are on betaflight 2.7.0 do the following instead:
1. in cli type: set fast_pwm_protocol = MULTISHOT (press enter)
2. type: save (press enter)
*If you are on betaflight 2.8.1 do the follwing instead:*
1. in cli type: set fast_pwm_protocol = MULTISHOT (press enter)
2. type: save (press enter)
NOTE: ONESHOT WILL DISABLE AUTOMATICALLY , this is normal now in this version.
**Further notes** If you are using the new Betaflight configurator on firmware 2.8.1 or higher, you can now select multishot straight from the config page! No CLI required.
Any questions leave a comment, don't forget to like and subscribe :)
Disclaimer: Please proceed with caution and follow this video guide entirely at your own risk.
Support me through affiliate links
(this helps me out if you shop via these links!)
Banggood
Gearbest
Or help me out directly
PART 1: Flashing your multicopter ESCs with Oneshot or Multishot!
In this tutorial we look at how to get BLhelisuite working with 'one-wire-passthrough' so you can flash or upgrade your ESCs with one simple USB connection to your flight controller. As well as upgrading your ESC firmware we will see how simple it is to switch over to Multishot using the same software, if you so desire!
BLHelisuite download page:
Multishot download page:
Multishot notes: Your motors will not operate until you enable multishot function in the cleanflight CLI. Do the following (betafligh 2.6.1)
1. Leave oneshot *enabled* very inportant for this version of betaflight.
2. in the cli type: set use_multishot =ON (then press enter)
3. type: save (press enter)
If you are on betaflight 2.7.0 do the following instead:
1. in cli type: set fast_pwm_protocol = MULTISHOT (press enter)
2. type: save (press enter)
*If you are on betaflight 2.8.1 do the follwing instead:*
1. in cli type: set fast_pwm_protocol = MULTISHOT (press enter)
2. type: save (press enter)
NOTE: ONESHOT WILL DISABLE AUTOMATICALLY , this is normal now in this version.
**Further notes** If you are using the new Betaflight configurator on firmware 2.8.1 or higher, you can now select multishot straight from the config page! No CLI required.
Any questions leave a comment, don't forget to like and subscribe :)
Disclaimer: Please proceed with caution and follow this video guide entirely at your own risk.
Support me through affiliate links
(this helps me out if you shop via these links!)
Banggood
Gearbest
Or help me out directly
Fpvracer.lt is not the owner of this text/video/image/photo content, the real source of content is Youtube.com and user declared in this page publication as Youtube.com user,
if you have any question about video removal, what was shared by open community, please contact Youtube.com directly or report bad/not working video links directly to video owner on Youtube.com. Removed video from Youtube.com will also be removed from here.