Happymodel Snapper7 The Most fun you can have with your Pants On

Snapper7 Link
Mobile Link
Support Grumpy Trev on Patreon
Snapper6 Video
********************************************************************
Package Inlcuded:
Basic Version
1x Snapper7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
1x 3.8v 450mah 30C/60C Lipo battery
1x USB Lipo/LIHV Charger
1x Propeller Disassemble Tool
1x Screwdriver
********************************************************************
Standard Version
1x Snapper7 75mm FPV Drone
4x 40mm 3-Blade Propellers ( 4 CW & 4 CCW)
3x 3.8v 450mah 30C/60C Lipo Battery
1x 1S06 6 Way Lipo/LIHV charger
1x Propeller Disassemble Tool
1x Screwdrive
********************************************************************
Specification:
Brand Name: Happymodel
Model: Snapper7
Item Name: 75mm Wheelbase 1S Brushless Whoop FPV Racing Drone
Wheelbase: 75mm
Version: Basic Version / Standard Version ( Optional)
- The diffirence of them are the package lipo battery and charger
Receiver: Compatible Frsky D8 Receiver OR
Compatible Flysky AFHDS/ AFHDS-2A Receiver ( Optional)
Size: 98.5mm*98.5mm*36mm
Weight: 28g (without battery)
********************************************************************
Crazybee F3 Flight Controller
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000 (SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Frsky receiver Or Flysky Receiver
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Firmware: Betaflight_3.3.0_Crazybee
Board size: 28.5 * 28.5MM
Board weight: 3.5 g
Heading LED Ready
********************************************************************
Onboard 5A 4 In 1 ESC
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Motor connector: JST PH1.25 3pin
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM
********************************************************************
Onboard Frsky Receiver Version ( Optional)
SPI BUS receiver
Frsky D8
Compatible both of Non EU and EU LBT transmitter
Channels: 8CH
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground) : 300m
********************************************************************
Onboaed Flysky Receiver Version ( Optional)
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch (AFHDS) or 14ch (AFHDS-2A)
No ground interference (Transmitter and receiver 1 m from the ground): 300m
Failsafe support
********************************************************************
SE0703 19000KV Motor
KV: 19000KV
Configu-ration: 9N12P
Stator Diamter: 7mm
Stator Length: 3mm
Shaft Diameter: Φ1.0
Motor Dimension (Dia.*Len) : Φ10*14.5
Weight: 2.5g
No.of Cells: 1S Lipo
********************************************************************
5.8G VTX AIO Camera
5.8G 48CH 25mW VTX
Output Power: 25mW
Frequency: 48CH
With Raceband: 5474-5945 MHZ
Input Voltage: 3.3V-5.5V
Current Consumption: 300mA (type)
700TVL Camera
Camera Resolution: 700TVL
Field of View: 120°
Video Format: NTSC
Antenna: RG178 antenna
Size: 13.9x12.0mm( LxW)
Weight: 3g
********************************************************************
3.8V 450mAh Lipo Battery
Capacity: 450mAh
Voltage: 3.8V
Continuous Discharge Rate: 30C
Instantaneous Discharge Rate: 60C
Size: 60x18x7mm
Weight: 13.6g
Connector: PH2.0
********************************************************************
FYI
These are affiliate or campaign links and the above product was sent for free.
If you dont like it, feel free to just google search the product or store and
get the link that way. But if it doesn’t bother you these links help support
the channel and also help vendors track the impact of my videos.
********************************************************************