BetaFPV Beta140 Maiden and Thoughts

Hello everyone welcome back.
So the maiden went well. I did end up upgrading the antenna on the wolfwhoop vtx. If you have any questions about this build please leave me a comment.
Want to support my channel? Below are affiliate links. Affiliate links help me to earn a commission and are of no cost to you. So if you are out and online shopping click one of my links and it will greatly help me continue to do what I do.
Here is all that went into the build.
BetaFPV Betas 140 Carbon Fiber Frame
Beta140 140mm FPV frame is ture X structure, made of carbon fiber frame, integrated 2.5mm carbon fiber unibody main plate
Design for 3 intch propeller, fit for 1306/1407 motor
Fit for flight controller with the mounting hole of 20*20mm
Frame weight is 35g only
Hobbymate 1306 3100kv Brushless Motors
Model: 1306
KV: 3100KV
Voltage: 2-4s Lipo
Motor Weight: 11.3g
HakRC 20x20 F3 Stack with a 4 in 1 20amp ESC
F3 flight control support CF / BF firmware ( by default BF 3.17 )
Support 2 - 4S power input
Support external LED and buzzer alarm
Comes with battery voltage detection
Support PPM / SBUS / DSM2 / DSMX receiver
Support OSD remote control
Integrated OSD: yes
Integrated BEC: 2A
Mounting hole space is 20 x 20mm
Specifications:
MPU: MPU6000
Microcontroller: STM32F303CCT6
BEC: 5V / 2A output
External LED: yes
External buzzer: yes
Product weight:12g
WolfWHoop TX2
Supports 48 channels
Tiny and low weights: under 2.2g
Power switchable: 0mW, 25mW, 200mW
Built-in U.FL connector rather than SMA
One cool feature about this VTX is that 0mW, you can adjustable your Parameter during a race with zero interference with any neighbor active channels
Gemfan 3052-3 Props
Weight: 1.65g (each)
Middle Mounting Hole: 5mm
Size: 3052, 3. 0x5. 2.
Suit for fpv 130mm 140mm frame.
Compatible with 1306-1806 brushless motors
Foxeer Lollipop Antenna
Root reinforcement design 360°protection
Low feeder loss,easy to install, can be bent at any angle maintain
Body adopt imported PC+ABS material, can withstand high strength impact
Double-jacket semi-rigid cable for heavy impact resistance
Foxeer Predator Micro 2
1000TVL
1.8mm
110 Degree
M8 Lens Super WDR
FPV Camera With OSD
DC5V-40V
Low Latency
BetaFPV 3s 450mah Lipo
Connector: XT30 plug
Size: 13*30*53mm, Weight: 44g
Continuous Discharge Rate: 35C
Thank you for watching.
What I fly and what I use
BNF Beta85
BNF Beta75s
BNF BetaFPV Beta 65
BetaFPV Beta 65 Frame Kit
BetaFPV Flight Controller with Frsky Receiver & BetaFlight OSD
BetaFPV Flight Controller with DSMX Receiver & BetaFlight OSD
BetaFPV Z01 Camera
BetaFPV 230mah LiHV Batteries
BetaFPV Replacement Canopies
BNF Beta 75s
BNF Beta 75
Beta 65s
FPV Goggles I use
Soldering Iron I use
I film all my videos with the Samsung Note 5
Thank you very much.
Fly Safe & Fly Often